Professional Disc Jockey Products
PA5Pro Preamplifier
OWNER’S MANUAL
NUMARK INDUSTRIES
111 Dupont Drive, Providence, RI 02907
P A5 P r o
NUMARK PA5Pro Preamplifier
INDEX
Safety Information
Product Registration
Page 2
Page 4
Introduction
Features
Precautions
Page 5
Page 6
Front Panel Diagram
and Features
Rear Panel Diagram
and Features
Page 7
Connection Diagram
Specifications
Page 9
Page 10
Page 11
Page 12
Block Diagram
Warranty and Service
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
3
P A5 P r o
CONGRATULATIONS!
You have purchased the PA5Pro Preamplifier by Numark. The Numark PA5-Pro is a
high-quality stereo preamplification unit. Perfect for a variety of applications such as
aerobics clubs, karaoke, restaurants, office music, bars, churches, or even nightclub off
peak time. This simple to operate unit allows you to select from 4 different input sources
such as a CD player or a tape deck and still page someone with the 2 microphones using
our integrated auto-muting feature.
Thank you for buying Numark products!
FEATURES...
• RCA,Balanced XLR Outputs
• Binding Post Outputs
• Record Output
• 2 Neutrik™ Mic inputs with
separate 3-band equalizers
• Auto mute with defeat switch
• Master 3-band Equalizer
• Input Selector Switch
• Loudness switch
• Stereo/Mono switch
• Headphone output
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
4
P A5 P r o
IMPORTANT INFORMATION...
Please read this entire manual before
connecting the PA5PRO to your system.
For optimum performance:
SYSTEM PRECAUTIONS
• Use appropriate cables throughout your
system: Quality shielded audio cables and
terminated shielded video cables, low-
capacitance preferred. Speaker cables must be
14-gauge minimum; 12- or 10-gauge is better.
• Always make sure that AC power is OFF
while making any connections.
• Do not use excessively long cables (i.e. over
50ft/14m) Be sure plugs and jacks are tightly
mated. Loose connections can cause hum, noise
or intermittents that could easily damage your
speakers.
• Reliability will be enhanced through the use of
banana connectors on the speaker wires.
Observe correct speaker wire polarity. If in
doubt, consult your Numark dealer or a qualified
technician.
• Never use spray cleaners on the slide
controls. Residues cause excessive dirt build-
up and this will void your warranty. In normal
use slide controls can last for many years. If
they malfunction (usually because of a dirty or
dusty environment) consult a professional
technician.
• Take care to connect only one cable at a time.
Pay attention to the color-coded, labelled Input
and Output jacks.
• ALWAYS remember: “TURN AMPS ON
LAST AND OFF FIRST”. Begin with master
faders or volume controls on minimum and the
amplifier gain/input control(s) down. Wait 8 to 10
seconds before turning up the volume. This
prevents transients which may cause severe
speaker damage.
• Never attempt to make any adjustments or
repairs other than those described in this
manual. Take the PA5PRO to your dealer or to
an authorized Numark Service Center.
• Use restraint when operating controls. Try to
move them slowly. Rapid adjustments could
damage speakers due to amplifier clipping.
A NOTE ON CABLES:
• Avoid amplifier “clipping” at all costs: this
occurs when the red LEDs (usually on the front
panel of most professional power amplifiers)
start flashing. “Clipping” is when the power
amplifier is distorting and working beyond it’s
limits. Amplifier distortion is THE major cause of
speaker failure.
Make the input and output
connections with readily
available low-capacitance stereo
cables. Quality cable makes a
big difference in audio fidelity and
punch. See your Numark dealer
or an electronics or audio
specialist store if you are not
sure which cables to get.
• To prevent fire or shock hazard, do not expose
the unit to rain or moisture. Never place cans
of beer, soda, glasses of water or anything
wet on top of the mixer!
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
5
P A5 P r o
PA5 PRO FRONT PANEL DIAGRAM AND FEATURES...
3
1
2
6 7
4
8
1 0
5
9
If the PA5PRO is your first preamplifier, please read this entire manual before you begin operation.
The PA5PRO can be rack-mounted or used as a free-standing unit (1-19" rack unit space).
1. Power Switch and Power-On LED.
5. 3-Band Master Equalizer (EQ). The EQ
compensates for differences in source material
sound quality. The EQ can be used to tailor the
sound to the acoustical requirements of the room.
The knobs have a center detent for an accurate "flat”
response. Start with this position if you've never
used a graphic EQ before and then slowly adjust the
bass, middle, or treble to a desirable position.
MIC SECTION
The PA5PRO has 2 extremely controllable
DJ Mic channels. The mute switch on the
rear panel (2) automatically reduces the level
of the music when the DJ Mic is spoken into.
2. Neutrik™ “Combo” connector allows
connection of either a 1/4” jack or an XLR jack. This
is ideal for connecting an XLR gooseneck directly
into the mixer.
6. The Loud button boosts the bass frequencies to
add more presence to the audio signal.
7. The Mono button is pressed to merge the left
and right channels of input to become the same
output.
3. Treble, Mid, and Bass Controls fine tune
the tone of your voice on both mics through the
sound system. The controls are detented for setting
tone "flat". For best results, use a dynamic cardioid
microphone.
8. The Input Selector determines which source
will be live to the outputs based on what you have
connected to the rear panel input section.
4. The DJ Mic volume controls the DJ Mic
volume for the Neutrik™ “Combo” connector.
9. The Master Volume controls the overall output
level and the headphone output level.
10. The Headphone jack is supplied so you may
monitor the output of the preamp directly.
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
6
P A5 P r o
PA5 PRO REAR PANEL DIAGRAM AND FEATURES...
1
2 3 4 5 6 7
8
9
1 0
1 1
1 2
1. GND is the grounding lug for turntables 1, 2 and 3
(phono inputs on Channels 1, 2 and 3). Always use
this connection (your turntable cable should have a
grounding wire).
7. The Tape Outputs are low-impedance
unbalanced RCA jacks which output the program
mix and allow you to connect any recording device.
8. The Stereo Main RCA Outputs are low-
impedance RCA connectors controlled by the
Master fader.
2. The Automute Switch should be set to the on
position if you want inputs 3-6 to lower volume
automatically when the microphones are spoken
through. Set it to the off position if you don’t want
the inputs affected.
9. The Stereo Binding Post Outputs are low-
impedance hard-wire connectors controlled by the
Master fader
3. Phono Inputs use unbalanced RCA jacks. Your
input signal is fed directly to the PA5PRO's high-
quality RIAA phono pre-amplifiers so use this
position only for moving magnet cartridges. Line
level sources will overload the sensitive phono pre-
amps and will sound very bad, so always be sure to
toggle the line/phono switch over to line before
connection of line sources.
10. The Stereo XLR Balanced Outputs are
balanced low-impedance outputs for connecting to
other balanced amplifiers or devices. Use these
outputs whenever possible for the best sound.
11. AC Cord. See safety precautions on page 3 for
proper treatment of the power cord.
4,5,6. CD,Tape, and Aux Line Inputs are
unbalanced RCA jacks. You can connect stereo
audio from HiFi VCRs, cassette and reel-to-reel tape
decks, DAT machines, CD players, laser discs,
tuners, even synthesizers or other mixing consoles.
NOTE:Plug mono audio sources into both Left and
Right inputs using a “Y” cable connector.
12. Voltage Selector should be set before you
plug the unit in to the correct voltage for your
location.
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
7
P A5 P r o
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
8
P A5 P r o
PA5 Pro CONNECTION DIAGRAM...
INSTALLATION AND OPERATION
Study the Connections Diagram. First, connect all stereo input sources. Next connect your
microphone(s) and monitor headphones. Make sure all volumes are at "zero" and the unit is off. Finally,
connect the stereo outputs to the power amplifier(s) and/or audio sources. Plug the PA5Pro into AC power.
Now you are ready to switch it on.
Microphone 1
Microphone 2
CD Pla ye r
Turnt a b le
AC
Out le t
Tune r
Re cording
Tape Deck
Tape Deck
Ma in
Sound Syst e m
w/ Am p lifie r
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
9
P A5 P r o
SPECIFICATIONS...
INPUTS:
Line:
Mic:
150 mV rms sensitivity
2.5 mV rms sensitivity
Phono: 2.5 mV rms sensitivity
OUTPUTS:
Line:
2V rms
EQUALIZER:
Bass/Mid/Treble control +-8dB
SIGNAL TO NOISE RATIOS (vs. maximum output):
Line:
Mic:
Phono:
Better than 95 dB
Better than 75 dB
Better than 75 dB
DISTORTION:
T.H.D. 0.05%
CROSSTALK:
Channel 60dB
Function 60dB
FREQUENCY RESPONSE:
Mic:
Line:
Phono:
20Hz-20kHz +_ .3dB
20Hz-20kHz +_ .5dB
20Hz-20kHz +_ 1dB
WEIGHT:
(net) 3.5Kg
DIMENSIONS:
WxHxD 483x45x280mm
19”x 1 3/4”x11 1/4”
POWER CONSUMPTION:
20 Watt
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
1 0
P A5 P r o
BLOCK DIAGRAM...
Numark - The Prove n Le ade r in DJ Te chnology
© 1 9 9 7 Num ark Indus t rie s
1 1
Professional Disc Jockey Products
Wa r r a n t y a n d Se r v ic e In f o r m a t io n
Numark Industries, LLC and Numark International, Inc. (hereafter “Numark”)
warrants each new product manufactured and/or supplied by it to be free from
defects in material or workmanship under conditions of normal use and service for
360 days, beginning on the date of purchase from an authorized Numark Dealer,
but not to exceed 2 years from date of shipment by Numark.
The Numark obligation under this warranty is limited to repairing or replacing, at
its option, the product or part(s) therein; which upon examination by Numark shall
appear to be defective or not up to factory specifications; providing the Numark
product is returned (transportation prepaid) to Numark.
Numark shall not be liable for any damages, consequential or otherwise,
resulting from the use and operation of this product and makes no other warranty(s)
either express or implied on this product, including any warranty of merchantability.
This warranty does not extend to any of our products which have been
subjected to misuse, neglect, accident, incorrect wiring not our own, improper
installation, or use in violation of instructions furnished by us, nor extended to units
which have been repaired or altered outside of our factory, nor to cases where the
serial number thereof has been removed, defaced, or changed, nor to accessories
used therewith not of our own manufacture. Numark reserves the right to make
changes or improvements in its products, during subsequent production, without
incurring the obligation to install such changes or improvements on previously
manufactured equipment.
To place this warranty into effect, the enclosed WARRANTY REGISTRATION
CARD must be returned to Numark Industries, LLC within thirty (30) days after
date of purchase.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Some states do not allow the exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may not apply to you.
EQUIPMENT TRANSPORT
A Return Authorization number should be obtained from Numark through the
addresses or phone numbers below.
It is the customer’s obligation, when returning faulty equipment, to properly
pack the Numark equipment in its original packaging. Failure to do so may
inadequately protect the equipment in transit and, therefore, jeopardize the
customer’s warranty. The defective Numark equipment should be sent, FREIGHT
PREPAID with Return Authorization number to:
NUMARK INDUSTRIES
111 Dupont Drive
Providence, RI 02907. U.S.A.
Attention: Service Department
Telephone: +1 (401) 946-4700
Fax: +1 (401) 946-5350
E-mail: [email protected]
|